Translock DL50 Bush
DL50 9 X 12mm Drivelock Bush
Variation Not Available
DL50/9
In Stock
£
2.96
Inc VAT
£
2.47
Ex VAT
DL50 9 X 12mm Drivelock Bush | DL50/9
Add to List
Remove from List
Add to Cart
SPECIFICATION
FURTHER INFO
DRIVELOCK® 50 Bushes
- Not self-centering
- Small radial dimensions
- Low torques 2.4 to 1300Nm
- Bores 6 to 70mm
- Can be stacked in series (up to 4) to increase torque
- Imperial bore also available*
| Machining data | |||
|---|---|---|---|
| Recommended shaft & hub tolerances for full torque transmission are: | |||
| < 40mm diameter | |||
| Shafts | H6 | Hub | H7 |
| > 40mm diameter | |||
| Shafts | H8 | Hub | H8 |
| Stock no. | d (mm) | D (mm) | L (mm) | T (Nm) | F (Nm) | P N/mm2 | Fa kN |
|---|---|---|---|---|---|---|---|
| DL50/ 6 | 6 | 9 | 4.5 | 2.4 | 0.84 | 75 | 3.8 |
| DL50/ 7 | 7 | 10 | 4.5 | 3 | 0.86 | 70 | 3.9 |
| DL50/ 8 | 8 | 11 | 4.5 | 4.7 | 1.17 | 90 | 5.3 |
| DL50/ 9 | 9 | 12 | 4.5 | 7.9 | 1.76 | 105 | 15.6 |
| DL50/ 10 | 10 | 13 | 4.5 | 9.5 | 1.91 | 105 | 15.6 |
| DL50/ 12 | 12 | 15 | 4.5 | 11.4 | 1.91 | 90 | 15.6 |
| DL50/ 13 | 13 | 16 | 4.5 | 13.1 | 2.02 | 90 | 15.6 |
| DL50/ 14 | 14 | 18 | 6.3 | 22.3 | 3.18 | 90 | 25.4 |
| DL50/ 15 | 15 | 19 | 6.3 | 24.3 | 3.24 | 85 | 25.4 |
| DL50/ 16 | 16 | 20 | 6.3 | 27.3 | 3.42 | 85 | 25.4 |
| DL50/ 17 | 17 | 21 | 6.3 | 29.8 | 3.51 | 85 | 25.4 |
| DL50/ 18 | 18 | 22 | 6.3 | 32.4 | 3.61 | 80 | 25.4 |
| DL50/ 19 | 19 | 24 | 6.3 | 49 | 5.22 | 110 | 36 |
| DL50/ 20 | 20 | 25 | 6.3 | 53 | 5.33 | 105 | 36 |
| DL50/ 22 | 22 | 26 | 6.3 | 66 | 6 | 115 | 36 |
| DL50/ 24 | 24 | 28 | 6.3 | 73 | 6.13 | 110 | 36 |
| DL50/ 25 | 25 | 30 | 6.3 | 72 | 5.77 | 95 | 36 |
| DL50/ 28 | 28 | 32 | 6.3 | 86 | 6.33 | 100 | 36 |
| DL50/ 30 | 30 | 35 | 6.3 | 91 | 6.08 | 85 | 36 |
| DL50/ 32 | 32 | 36 | 6.3 | 131 | 8.24 | 115 | 45 |
| DL50/ 35 | 35 | 40 | 7 | 171 | 9.77 | 110 | 54 |
| DL50/ 36 | 36 | 42 | 7 | 169 | 9.39 | 100 | 54 |
| DL50/ 38 | 38 | 44 | 7 | 181 | 9.55 | 95 | 54 |
| DL50/ 40 | 40 | 45 | 8 | 231 | 11.57 | 105 | 66 |
| DL50/ 42 | 42 | 48 | 8 | 235 | 11.22 | 95 | 66 |
| DL50/ 45 | 45 | 52 | 10 | 353 | 15.71 | 95 | 99 |
| DL50/ 48 | 48 | 55 | 10 | 572 | 23.44 | 135 | 132 |
| DL50/ 50 | 50 | 57 | 10 | 602 | 24.08 | 130 | 132 |
| DL50/ 55 | 55 | 62 | 10 | 670 | 24.35 | 125 | 132.0 |
| DL50/ 56 | 56 | 64 | 12 | 790 | 28.20 | 115 | 157.2 |
| DL50/ 60 | 60 | 68 | 12 | 860 | 28.60 | 110 | 157.2 |
| DL50/ 70 | 70 | 79 | 14 | 1300 | 37.10 | 110 | 200 |
DL50 consists of a pair of conical rings and can be used in series (up to 4 sets) to give higher torque ratings.
Note: Customer to supply clamping ring or equipment